WASHER-DRYER
WJS 1382
124976950
INSTRUCTION BOOKLET
CONTENTS
Warnings
4
Maintenance
18
■
■
■
■
■
■
Bodywork
18
18
18
19
19
19
Description of the appliance
5
5
Detergent dispenser drawer
Drain filter
■
Detergent dispenser drawer
Water inlet filter
Technical specifications
Installation
5
Emergency emptying out
Frost precautions
6
■
Transit devices
6
6
7
7
8
Something not working?
20-21
■
Positioning
■
Water inlet
■
Water drainage
■
Electrical connection
Use
9
■
Control panel
9
9
■
Controls
■
Programme selection
10
■
Washing and drying hints
11
Sorting the laundry
Temperatures
11
11
Before loading the laundry
Maximum loads
11
11
Removing stains
Detergents and additives
Drying
11
12
12
■
International wash code symbols
13
■
Operating sequence
14-15
16-17
■
Washing and drying programmes
3
WARNINGS
It is important that this instruction book be kept with the appliance for future reference. If you sell or
give the appliance away, make sure that the book is passed to the new owners so that they can
familiarise themselves with its operation and relevant warnings.
The following warnings are provided in the interests of overall safety. You must read them carefully
before installing or using the appliance.
■
Do not overload the appliance. Follow the
instructions in the instruction book.
General warnings
■
When unpacking the appliance, check that it
■
■
Make sure that all pockets are empty. Objects
such as coins, safety pins, pins and screws
can cause extensive damage.
is not damaged. If in doubt, do not use it and
contact the Service Centre.
■
This appliance is designed to be used by
Do not machine wash garments saturated
with petroleum, methylated spirits,
trichlorethylene, etc. If such fluids have been
used to remove stains prior to washing, wait
until they have completely evaporated from
the fabric before placing garments in the
appliance.
adults. Children must not be allowed to touch
the controls or play with the product.
■
During high temperature washing and drying
cycles the glass door becomes very hot. Do
not touch it.
■
Pets sometimes climb into washing
machines. Check the drum before each use.
■
Place small items such as socks, belts, etc. in
a cloth bag or pillowcase to prevent them
getting trapped between the drum and the
tub.
Installation
■
All internal packing must be removed before
using the appliance. Serious damage may be
caused to the machine or adjacent furniture if
the protective transit devices are not removed
or are not completely removed. Refer to the
relevant paragraph in the instruction book.
■
■
Use only the recommended quantities of fabric
softener. An excessive amount could damage
the laundry.
Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the
door seal and prevents the formation of
musty smells.
■
■
Any electrical work required to install this
appliance must be carried out by a qualified
electrician.
■
Always check that water has emptied out
before opening the door. If not, drain the
water following the instructions in the
instruction book.
Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
■
■
After having installed the machine, check that
it is not standing on its electrical supply cable.
■
Always unplug the appliance and shut the
water tap after use.
If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between
the adjustable feet and the floor.
Service/repair
■
In the event of a fault, do not attempt to repair
the appliance yourself. Repairs carried out by
inexperienced persons may cause damage.
Use
■
This appliance is designed for domestic use.
■
If repairs are needed, contact an authorised
service centre and ask for genuine spare
parts.
It must not be used for purposes other than
those for which it was designed.
■
■
Only wash and dry fabrics which are
designed to be machine washed and dried.
Follow the instructions on each garment
label.
If you use a liquid detergent with a dispenser
which has to be placed directly in the drum,
remember to remove this dispenser before
drying.
4
DESCRIPTION OF THE APPLIANCE
1
2 3 45
6
7
8
01 Detergent dispenser drawer
02 Drying pilot light
03 Drying time selector dial
04 Spin speed reduction button
05 On/Off button
9
06 Temperature selector dial
07 Operating pilot light
08 Programme selector dial
09 Programme card
10
11
10 Door locked light
11 Door handle
12 Filter
12
13 Adjustable feet
13
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
P0260
TECHNICAL SPECIFICATIONS
DIMENSIONS
MAXIMUM LOAD
SPIN SPEED
Height
Width
Depth
85 cm
60 cm
60 cm
WASHING
6.5 kg
DRYING
3.00 kg
2.00 kg
-
-
Cotton
Synthetics
Delicates
Woollens
2.5 kg
2.0 kg
1.0 kg
1300 rpm max.
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
220-230 V/50 Hz
2200 W
MINIMUM FUSE PROTECTION
10 A
WATER PRESSURE
Minimum
Maximum
5 N/cm2
80 N/cm2
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility
5
INSTALLATION
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine on its
back, taking care not to squash the hoses.
This can be avoided by placing one of the
corner packing pieces between the machine
and the floor.
P0255
2. Remove the polystyrene block from the bottom
of the machine and release the two plastic
bags by removing the adhesive strip.
3. Carefully remove the right-hand bag (1) then
the left-hand bag (2) by pulling them towards
the centre of the machine.
2
1
P0234
P0233
4. Set the machine upright and remove the two
remaining bolts from the back.
5. Pull out the three plastic spacers from the
holes into which the bolts were fitted.
6. Plug the open holes with the plugs which you
will find in the plastic bag containing the
instruction booklet.
P0020
P0256
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units.
Carefully level by screwing the adjustable feet in
or out. Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
P0254
P0509
After having levelled the machine, tighten the lock
nuts.
6
Water inlet
Connect the water inlet hose to a tap with a 3/4"
thread after having inserted the small filter “A”
supplied with the machine.
The other end of the inlet hose which connects to
the machine can be turned in any direction.
Simply loosen the fitting, rotate the hose and
retighten the fitting, making sure there are no
water leaks.
A
P0003
P0021
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you
will have to purchase a new, longer hose
specially designed for this type of use.
Water drainage
The end of the drain hose can be positioned in
three ways:
Hooked over the edge of a sink using the
plastic hose guide supplied with the machine.
In this case, make sure the end cannot come
unhooked when the machine is emptying.
This could be done by tying it to the tap with a
piece of string or attaching it to the wall.
In a sink drain pipe branch. This branch must
be above the trap so that the bend is at least
60 cm above the ground.
P0022
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter of
the drain hose.
The drain hose must not be kinked. Run it along
the floor; only the part near the drainage point
must be raised.
P0023
7
Electrical connection
This machine is designed to operate on a
220-230 V, single-phase, 50 Hz supply.
Check that your domestic electrical installation
can take the maximum load required (2.2 kW),
also taking into account any other appliances in
use.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
The appliance is supplied with a 13 amp plug
fitted.
In the event of having to change the fuse in the
plug supplied, a 13amp ASTA approved
(BS1362) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
GREEN & YELLOW
E
Brown
L
The wire coloured green and yellow must be
connected to the terminal marked with the letter
N
«E» or by the earth symbol
green and yellow.
or coloured
BROWN
BLUE
CORD CLAMP
P1041
The wire coloured blue must be connected to
the terminal «N» or coloured black.
The wire coloured brown must be connected to
the terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must
be secure over the outer sheath.
WARNING:
A cut off plug inserted into a 13 amp
socket is a serious safety (shock)
hazard.
Ensure that the cut off plug is disposed
of safely.
8
USE
Control panel
30º- 40º
60º- 95º
40º- 60º
30º- 40º
40º- 60º
30º- 40º
30º- 40º
A
B
C
D
F
A
H
K
L
M
N
G - 1300
J - 650
2 kg
110'- 120'
90' 100'
1 kg
60'- 70'
40'- 50'
3 kg
1.5kg
90'- 100'
70'- 80'
50'- 60'
30'- 40'
-
1
2 3
4 5
6
7
8
1 Detergent dispenser drawer
5 On/Off button
Press this button to start the machine, press
again to interrupt a programme or switch off the
power supply to the machine.
2 Drying pilot light
It illuminates when drying starts.
6 Temperature selector dial
Turn this dial clockwise or anti-clockwise to select
the required temperature.
3 Drying time selector dial
Graduated up to 120 minutes for cotton and
synthetics, allows drying time to be selected
according to the type and amount of laundry and
the required degree of dryness:
- blue sector for cotton
Position
means that the machine will wash
with cold water.
Press the dial to pop it out.
- green sector for synthetics
Turn the dial clockwise only.
7 Operating pilot light
This light is on whilst the machine is operating
and goes out when the ON/OFF button is
pressed again.
Cooling phase
To allow the laundry to cool down, a cooling
phase starts automatically 10 minutes before the
end of drying and this phase must in no
circumstances be reduced or interrupted.
8 Programme selector dial
To select the required programme, turn this dial
clockwise until the programme letter is exactly
opposite the pointer.
4 Spin speed reduction button
By depressing this button the spin speed is
reduced as follows:
Press the dial to pop it out.
- cotton, linen: from 1300 to 650 rpm
- programme M (short spin) and A (extra
prewash): from 650 to 450 rpm.
We suggest you not to press this button, when
you have to machine dry laundry in order to save
energy and time.
9
Programme selection
■
■
Automatic washing and drying
(NON-STOP programme)
Washing only
Load size:
Automatic washing and drying is only
possible with linen, cotton and synthetics
programmes.
The maximum load size is 3 kg for cotton
and 2 kg for synthetics.
– cotton, linen
– synthetics, delicate fabrics
– woollens
max 6.5 kg
2.5 kg
1.0 kg
– Place the detergent and additive in the
dispenser drawer.
Do not exceed these quantities.
– Select the temperature and the wash
programme.
– Select the temperature and the wash
programme.
– Press button
if required.
– Select the drying time in the relevant
sector.
– Press the ON/OFF button
.
– Press the ON/OFF button
.
■
Drying only
Load size:
– cotton, linen
– synthetics
The laundry will be washed and dried without
any further action by you.
max 3 kg
2 kg
– Select the drying time in the relevant
sector.
– Select the drying programme G or J.
– Press the ON/OFF button
.
10
i
Washing a maximum load makes the most
efficient use of water and energy.
Washing and drying hints
For heavily soiled laundry, reduce the load size.
Sorting the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
Laundry weights
The following weights are indicative:
whites, coloureds, synthetics, delicates, woollens.
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
Temperatures
95°
for normally soiled white cottons
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
towelling towel
tea cloth
60°
for normally soiled, colour fast
garments (e.g. shirts, night dresses,
pyjamas....) in linen, cotton or
synthetic fibres and for lightly soiled
white cotton (e.g. underwear).
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
(cold)
30°-40°
for delicate items (e.g. net curtains),
mixed laundry including synthetic
fibres and woollens bearing the
label «pure new wool, machine
washable, non-shrink».
men’s underpants
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their “whiteness” in the wash.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab
the stain; treat several times.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins, pins).
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent
or detergent paste.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and
the fabric tends to hole.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Maximum loads
Recommended loads are indicated in the
programme charts.
Grass: soap lightly and treat with bleach (whites
and fast coloureds only).
General rules:
Ball point pen and glue: moisten with acetone
(*), lay the garment on a soft cloth and dab the
stain.
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove any
residual marks from white fabrics with bleach.
Delicate fabrics and woollens: drum no more
than one third full.
11
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the detergent
dispenser drawer.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
Water hardness is classified in so-called
“degrees” of hardness. Information on hardness
of the water in your area can be obtained from
the relevant water supply company, or from your
local authority.
(*) do not use acetone on artificial silk
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
– you are washing a small load
– the laundry is lightly soiled
– large amounts of foam form during washing.
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of
soiling.
Degrees of water hardness
Degrees
Level
Characteristic
German
°dH
French
°T.H.
All commonly available washing machine
detergents may be used in this appliance:
0,0-15
16-25
1
2
3
4
soft
medium
hard
00-07
08-14
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (60°C
max) and woollens,
26-37
15-21
more than 37
very hard
more than 21
– liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
Drying
■
All laundry to be dried must be thoroughly
spun. The higher the spin speed, the lower
the power consumption and the shorter the
drying time.
The detergent and any additives must be placed
in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
■
■
If using concentrated powder or liquid
detergents, a programme without prewash must
be selected.
Scrupulously follow the instructions on each
garment label, making sure that it is suitable
for tumble-drying.
The washing machine incorporates a
recirculation system which allows an optimal use
of the concentrated detergent.
Do not tumble dry the following:
– wool, silk, synthetic curtains;
– articles with a plasticised finish, nylon
tights or stockings, sleeping bags, quilts,
articles made of foam rubber or containing
materials similar to foam rubber, fabrics
with metal inserts;
Pour liquid detergent into the dispenser drawer
compartment marked
the programme.
just before starting
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
– fabrics which tend to fray.
Important: during the drying cycle, the water
tap must be left open and the drain hose must
be correctly positioned.
12
i
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
30
95
60
40
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Hand wash
Do not
wash
at all
Delicate wash
Bleaching
Ironing
30
60
40
40
Bleach in cold water
Do not bleach
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
A
Dry cleaning
in all solvents
F
P
Dry cleaning
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
Do not
dry clean
pure alcohol
and R 113
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
Tumble dry
Do not
tumble dry
13
i
Operating sequence
Automatic washing and drying
(non-stop programme)
This option is only possible for cottons and
synthetics.
Maximum load:
– cotton, linen 3 kg
– synthetics 2 kg
Before washing your first load of laundry, we
recommend that you run a cotton cycle at 60°C,
with the machine empty, in order to remove any
manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main
wash compartment and start up the machine.
1. Place the laundry in the drum
Open the door.
Place the laundry in the drum, one item at a
time, shaking them out as much as possible.
Close the door.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent
recommended by the manufacturer in a
graduated cup and pour it into the main wash
compartment
.
If you wish to carry out the extra prewash, pour
detergent into the appropriate compartment
P0226S
marked
.
3. Measure out the additive
If required, pour fabric softener into the
compartment marked
without exceeding
the «MAX» mark.
Cl
P0222
4. Select the temperature
Turn the dial to the required setting.
95
°
P0464
14
5. Select the drying time
Turn the selector dial clockwise to the required
time setting (blue or green sector).
90
M0022S
6. Select the programme and start
the machine
Turn the programme selector dial clockwise to
the required programme and press the On/Off
button: the operating pilot light and door locked
light come on and the machine starts to operate.
B
P0471
P0465
7. At the end of the programme
The machine stops automatically.
Wait one or two minutes before opening the
door to give the electric locking mechanism time
to release it.
The door can be opened when the door locked
pilot light is off.
Depress the On/Off button again to switch the
machine off. The operating pilot light goes out.
Remove the laundry.
Turn the drum by hand to make sure it is
completely empty, so as to avoid any forgotten
items being damaged in a subsequent wash
(e.g. shrinking) or their colour running into a
load of whites.
Release any buttons which have been pressed.
Turn the water tap off and unplug the machine.
Leave the door ajar to air the machine.
15
Energetic programmes for cotton and linen
Maximum load: washing 6.5 kg
washing+drying 3 kg
Washing
Possible
option
Progr.
Temp.
Type of laundry
Cycle description
Wash at 60°-95°C
3 rinses
Long spin
Whites,
normally soiled
60°-95°
B
Wash at 40°-60°C
3 rinses
Long spin
Coloureds,
normally soiled
40°-60°
C
D
F
3 rinses with additive
Long spin
Rinses
Spin
Drain and long spin
Prewash at 30°-40°C
Short spin
Extra prewash
30°-40°
A
The temperatures indicated are the optimum temperatures for each programme and depend on the
type of laundry and degree of soiling.
Drying: maximum load 3 kg
Drying time selector 0-120 min, blue sector.
Time
mins.
Programme
Type of laundry
Degree of drying
Quantity
3.0 kg
1.5 kg
90-100
50-60
Store dry
Cotton and linen spun
at 1300 rpm
G
3.0 kg
1.5 kg
70-80
30-40
Iron dry
16
Delicate programmes for synthetics, mixed fibres, delicates
woollens
and
Maximum load: washing 2.5 kg (woollens 1 kg)
washing+drying (synthetics) 2 kg
At the end of these programmes, the last rinse water is not emptied out, so as to avoid creasing of the
fabrics. To empty out the water, select programme M or N.
Important: When the automatic NON-STOP washing plus drying programme is used, the water is
emptied out automatically and there is a short spin before drying starts.
Washing
Possible
option
Progr.
Temp.
Type of laundry
Synthetics,
Cycle description
Wash at 40°-60°C
3 rinses
Stop with water in drum
40°-60°
H
normally soiled
Wash at 30°-40°C
3 rinses
Stop with water in drum
Delicate fabrics,
silk
30°-40°
30°-40°
K
L
Wash at 30°-40°C
3 rinses
Stop with water in drum
Woollens
Short spin
Drain
Drain and short spin
Empty out water
M
N
Extra prewash
(not for wool)
Prewash at 30°-40°C
Short spin
30°-40°
A
The temperatures indicated are the optimum temperatures for each programme and depend on the
type of laundry and degree of soiling.
Drying: maximum load 2 kg
Drying time selector 0-120 min, green sector.
Time
mins.
Programme
Type of laundry
Degree of drying
Quantity
2 kg
1 kg
110-120
60-70
Store dry
Synthetics,
spun at 650 rpm
J
2 kg
1 kg
90-100
40-50
Iron dry
17
MAINTENANCE
1. Bodywork
Clean the outside of the machine with warm
water and a neutral, non-abrasive household
detergent. Rinse with clean water and dry with a
soft cloth.
Important: do not use methylated spirits,
solvents or similar products to clean the
bodywork.
2. Detergent dispenser drawer
After a while, detergents and fabric softeners
leave deposits in the drawer.
Clean the drawer from time to time by rinsing it
under a running tap. To remove the drawer from
the machine, press the button in the rear left-
hand corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
P0224S
P0225S
Detergent can also accumulate inside the
drawer recess: clean it with an old toothbrush.
Refit the drawer after cleaning.
P0038
3. Drain filter
The drain filter collects threads and small
objects inadvertently left in the laundry. Check
regularly that the filter is clean.
Open the filter door.
Place a container under the filter and unscrew it.
P0861
P0860
Pull out the filter.
Clean the filter under a running tap, then refit it,
screwing it fully in.
P0040
P0859
18
4. Water inlet filter
If you notice that the machine is taking longer to
fill, check that the filter in the water inlet hose is
not blocked.
Turn off the water tap.
Unscrew the hose from the tap and remove the
filter.
Clean it with a stiff brush.
P0041
Refit the filter and screw the hose back onto the
tap.
5. Emergency emptying out
If the water is not discharged (outlet pump is
blocked, filter or outlet hose are clogged),
proceed as follows to empty out the machine:
■
pull out the plug from the power socket;
■
close the water tap;
■
if necessary, wait until the water has cooled
down;
■
place a bowl on the floor;
■
put the outlet hose end into the bowl and let
the water come out.
Should it not be possible to have access to the
outlet hose because, for example, the appliance
is built in the kitchen furniture, slightly loosen the
outlet filter after placing a bowl on the floor, to let
the water come out slowly.
At the end screw the filter again.
6. Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
■
Close the water tap and unscrew the water
inlet hose from the tap.
■
Place the end of the outlet hose and that of
the inlet hose in a bowl placed on the floor.
■
Select programme N (drain) and run it until
the machine stops.
■
Remove the plug from the socket.
■
Screw the water inlet hose back on and put
the outlet hose back in its place.
By doing this, any water remaining in the
machine is removed, avoiding the formation of
ice and, consequently, breakage of the affected
parts.
When you use the machine again, make sure
that the ambient temperature is above 0°C.
19
SOMETHING NOT WORKING?
Problems which you can resolve yourself
Problem
Possible cause
■ Check that the door is firmly closed.
■
The machine does not start up:
■ Check that the machine is plugged in and
that there is power at the socket.
■ Check that the main fuse and the fuse in the
plug has not blown.
■ Check that the programme selector dial is
positioned correctly and the ON/OFF button
depressed.
■ Check that the water tap is open.
■
The machine does not fill:
■ Check that water is coming out of the tap.
■ Check that the inlet hose is not squashed or
kinked.
■ Check that the filter in the inlet hose is not
blocked.
■ Check that the door is closed.
■ Check that the drain hose is not squashed or
■
The machine does not empty
and/or does not spin:
kinked.
■ A programme which stops with water in drum
has been selected.
■ Check that the laundry is evenly distributed in
the drum.
■ Too much detergent or unsuitable detergent
■
There is water on the floor:
(creates too much foam) has been used.
■ Check whether there are any leaks from one
of the inlet hose fittings. It is not always easy
to see this as the water runs down the hose;
check to see if it is damp.
■ Check that the drain hose is not damaged.
■ Too little detergent or unsuitable detergent
■
Unsatisfactory washing results:
has been used.
■ Stubborn stains have not been treated prior
to washing.
■ The correct temperature/programme was not
selected.
■ Excessive laundry load.
■ Check that all the transit bolts and packing
■
The machine vibrates or is noisy:
have been removed.
■ Check that the machine is not resting against
anything.
■ Check that the support feet are resting firmly
on the ground and that the lock nuts are
securely tightened.
■ Check that the laundry is evenly distributed in
the drum.
■ Maybe there is very little laundry in the drum.
20
■ The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage”
section.
■
■
The machine fills then empties
immediately:
■ The programme is still running.
The door will not open:
■ The door lock has not been released.
■ There is water in the drum.
The door can be opened when the door
locked light is off.
■
The electronic unbalance detection device
■
Spinning starts late or the
machine does not spin:
has cut in because the laundry is not evenly
distributed in the drum. The laundry is
redistributed by reverse rotation of the drum.
This may happen several times before the
unbalance disappears and normal spinning
can resume. If, after 10 minutes, the laundry
is still not evenly distributed in the drum, the
machine will not spin. In this case,
redistribute the load manually and reselect
the spin programme.
■ The machine is fitted with a commutator
motor which makes an unusual noise
compared with other traditional machines.
This motor enables a softer start to the spin
and controls the increase in spin speed
better. In this way, machine performance is
improved.
■
The machine makes an unusual
noise:
■ The machine, which is the result of modern
technology, runs in a very economical way
with low water consumption. Performance is
nevertheless excellent.
■
■
Water is not visible in the
machine:
■ The drying time has not been selected.
■ The tap is closed.
The machine does not dry or the
laundry is not dry enough:
■ The drain filter is blocked.
■ A suitable drying time in the correct sector
has not been selected.
■ The drum is overloaded.
■ You have selected option
before drying.
If you are unable to identify or solve the
Mod.
..........
Ser.
problem, contact our service centre. Before
telephoning, make a note of the model, serial
number and purchase date of your machine: the
Service Centre will require this information.
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042
21
Made in Italy
Z
|